Products · Waterproofing coatings

Waterproofing coatingsSeal leaks without removing sheets

From exposed metal roofs to wet rooms and leaking tiled walls. On metal roofs, AEW320 with polyester fabric seals screws, laps and gutters with a fabric-reinforced 3-coat seal, then coats the whole roof if needed.

  • AEW320: 527% elongation, watertight at 0.3 MPa (third-party tested)
  • Cold-applied, water-based options — no open flame
  • Exposed roofs, concrete, wet rooms, walls
  • No MOQ · 20 kg pails · ships 3–5 days after payment

Which product where?

WhereProductNote
Exposed metal roofs: screws, laps, gutters, skylightsAEW320Fabric-reinforced 3-coat seal at joints; 2–3 coats over the whole roof
Flat concrete roofs, old membrane roofsLMC340 or AEW320Seamless liquid membrane, no torching
Exposed roofs and joints with movementJSF310-01 (Type I)Flexible cementitious, ≥ 200% elongation
Wet rooms, water tanks, basementsJSF310-02 (Type II) or PUC350Tile directly onto JSF310-02; PUC350 needs a protective layer
Leaking tiled, painted or stone wallsTWC330Clear coating, finish unchanged

Products

TYS-AEW320 Elastomeric Acrylic Roof Waterproofing Coating

TYS-AEW320Exposed roof

Elastomeric Acrylic Roof Waterproofing Coating

Stop metal roof leaks without new sheets: fabric-reinforced 3-coat seal at the joints and full coverage where needed. 527% elongation, watertight at 0.3 MPa.

  • Elastic: 527% elongation at break, 1.5 MPa tensile strength
  • Watertight at 0.3 MPa for 30 min (third-party tested)
  • Can be left exposed; the white film also reflects heat
  • With polyester fabric: seals laps, screws, gutters and skylights
  • Cold-applied, single-component; can go over old bitumen or membrane

Used for

  • Metal roof leak repair: laps, screw holes, gutters, ridges, skylights
  • Concrete roofs, aged bitumen roofs and old membranes
  • Warehouses and grain stores where open flame is not allowed
PropertyResultBasis
Elongation at break527%Std ≥ 300% · CTC WT2021B01C03937
After heat ageing / acid / alkali276% / 584% / 581%Std ≥ 200%
Tensile strength1.5 MPaStd ≥ 1.0 MPa
Watertightness (0.3 MPa, 30 min)Watertight
Low-temperature flexibility−10 °C, no cracks
Solids content69%Std ≥ 65%
DryingTouch 1 h 40 min; through 2 h 30 min

Third-party data: CTC test report WT2021B01C03937 (6 January 2022), meets JC/T 864-2008 Type I.

Consumption
0.33–0.5 kg/m² per coat; ≥ 1.2 kg/m² total on the main roof
Coats
Joints: coat + fabric + 2 coats (≥ 100 mm each side). Roof: 2–3 coats, crossed
Colours
White (reflects heat), grey; others on request
Packing
20 kg pail · no MOQ

Get a price · AEW320Request the data sheet

TYS-LMC340 Liquid Membrane Waterproofing Coating

TYS-LMC340Seamless membrane

Liquid Membrane Waterproofing Coating

For re-doing old membrane roofs and flat concrete roofs: forms a continuous, seamless layer — no laps, no torching.

  • No seams, no laps — no lap leaks
  • Elastic, follows substrate movement and cracks
  • No torching: open and apply, cold
  • Bonds to metal, concrete and old membrane
  • Water-based — suitable for fire-sensitive stores

Used for

  • Roofs, gutters, balconies, basement walls and tanks
  • Waterproofing and damp-proofing large warehouses and grain stores
  • Renewing old roof waterproofing
PropertyResultBasis
CompositionSingle-component, water-based
Consumption
0.33–0.5 kg/m² per coat
Coats
2–3, crossed; reinforce joints and corners with fabric
Packing
20 kg pail · no MOQ

Get a price · LMC340Request the data sheet

TYS-JSF310-01 Polymer Cement Waterproofing Coating (Type I)

TYS-JSF310-01Flexible

Polymer Cement Waterproofing Coating (Type I)

Flexible waterproof layer for exposed roofs and joints that move: elongation ≥ 200%, can be applied to damp surfaces.

  • Flexible, crack-bridging: elongation ≥ 200%
  • −10 °C flexibility, no cracks
  • Damp substrates OK (no standing water); cold-applied
  • Can be reinforced with fabric
  • Two-component, water-based, solvent-free

Used for

  • Exposed roofs (metal, flat or pitched concrete) — new and repair
  • Basements and tunnels
  • Joints in lightweight walls and prefabricated buildings
PropertyResultBasis
Solids content≥ 70%GB/T 23445 Type I requirement
Tensile strength≥ 1.2 MPa
Elongation at break≥ 200%
Low-temperature flexibility−10 °C, no cracks
Bond strength≥ 0.5 MPa
Watertightness0.3 MPa, 30 min
Consumption
0.33–0.5 kg/m² per coat
Coats
2–3, crossed; ≥ 1.5 mm total on roofs
Packing note
Liquid and powder in matched sets
Packing
20 kg pail · no MOQ

Get a price · JSF310-01Request the data sheet

TYS-JSF310-02 Polymer Cement Waterproofing Coating (Type II)

TYS-JSF310-02High strength

Polymer Cement Waterproofing Coating (Type II)

For wet rooms, tanks and basements under constant water: tensile strength ≥ 1.8 MPa, and tiles can be laid directly on it.

  • High strength: ≥ 1.8 MPa
  • Negative-side impermeability ≥ 0.6 MPa — no blistering under water
  • Bond ≥ 0.7 MPa; damp substrates OK
  • Tile directly onto the film
  • Two-component, water-based, no solvent odour

Used for

  • Bathrooms, kitchens and balconies
  • Water tanks and pools
  • Basement slabs and walls, positive and negative side
PropertyResultBasis
Solids content≥ 70%GB/T 23445 Type II requirement
Tensile strength≥ 1.8 MPa
Elongation at break≥ 80%
Bond strength≥ 0.7 MPa
Watertightness0.3 MPa, 30 min
Impermeability (mortar, negative side)≥ 0.6 MPa
Consumption
0.33–0.5 kg/m² per coat
Coats
2–3, crossed
Packing note
Liquid and powder in matched sets
Packing
20 kg pail · no MOQ

Get a price · JSF310-02Request the data sheet

TYS-PUC350 Polyurethane Waterproofing Coating

TYS-PUC350Protected areas

Polyurethane Waterproofing Coating

For basements, wet rooms and car parks under a protective layer: elongation ≥ 500%, no cracks when bent at −35 °C.

  • Seamless: reaction-cured, one continuous film over complex details
  • Tensile ≥ 2.0 MPa, elongation ≥ 500%
  • −35 °C bending, no cracks
  • Watertight at 0.3 MPa for 120 min
  • Single-component, ready to use

Used for

  • Basements, bathrooms, kitchens, balconies, pools and car parks
  • Non-exposed roofs and permanently damp areas
  • Moving areas such as trafficked roofs (with a protective layer)
PropertyResultBasis
Solids content≥ 85%GB/T 19250-2013
Tensile strength≥ 2.0 MPaType I requirement
Elongation at break≥ 500%
Tear strength≥ 15 N/mm
Low-temperature bending−35 °C, no cracks
Watertightness0.3 MPa, 120 min
Consumption
0.33–0.5 kg/m² per coat
Coats
2, crossed
Note
Cover with a protective layer; not for long-term exposure
Packing
20 kg pail · no MOQ

Get a price · PUC350Request the data sheet

TYS-TWC330 Clear Waterproofing Coating for Walls

TYS-TWC330Clear

Clear Waterproofing Coating for Walls

Leaking walls, kitchens, bathrooms and balconies — no tiles broken, no render stripped. Two clear coats keep the existing finish.

  • No tile removal, no stripping: clean, seal and coat
  • Clear film keeps the look of tiles, paint or stone
  • Elastic seal across hairline cracks
  • Indoor and outdoor
  • Water-based, low odour

Used for

  • Aged, cracked painted walls leaking in rain
  • Poorly grouted tiles; leaks around windows and door frames
  • Kitchen, bathroom and balcony tiles — repaired without breaking tiles
  • Walls whose appearance must not change
PropertyResultBasis
AppearanceMilky liquid, dries clear
Suitable finishesTiles, wall paint, stone, fair-faced concrete
ApplicationRoller, brush or low-pressure spray
Coats
2 thin, even coats
Note
Repair hollow or loose finishes and structural cracks first
Packing
20 kg pail · no MOQ

Get a price · TWC330Request the data sheet

Buying questions

Is there a minimum order?
No MOQ on standard products. Everything is packed in 20 kg pails.
Can we get samples?
Yes. Samples are charged, and the cost is refunded on your first order.
How fast do you ship?
Within 3–5 days after payment.
How much AEW320 for a metal roof?
Main roof: at least 1.2 kg/m² in 2–3 coats. Joints: a fabric-reinforced 3-coat seal, at least 100 mm each side. Send us the area and the number of joints and we'll calculate it.
Which product for which job?
Use the table at the top of this page, or send us photos and tell us where it's going. Our engineers will specify it.
Will you help our applicators?
Yes. We send full application instructions and train your applicators by video. For larger projects our technician can come to site to set the specification and supervise the first areas.

Want this range under your own brand?

OEM from 5 tonnes, with packaging printed to your design. Custom development with no fee and first samples in one week. Coating manufacturers can also produce locally with our core materials.

Request a quote for waterproofing coatings

Tell us what you need. Photos of the roof help us answer faster.

  • Project enquirySend roof photos, the area and what's wrong — heat, rust or leaks. We'll tell you how we'd fix it and quote item by item.
  • Product enquiryTell us the products, where they're going (roof type, wet room, wall), the area and the destination.

We reply by email within one working day.

I need
Problem (tick all that apply)
Tap to choose photos, or drag them here

We use your details only to answer this enquiry.